1/5L Pro-Kleen Troll's Breath Iron Contamination Fallout Remover
You may also like
Product information
Pro-Kleen Troll's Breath is an Iron-Contamination remover that is safe to use on all lacquered paint work, chrome, glass, plastic, stainless steel, wheels and even rubber, that has a special colour indicator! Once the Troll's Breath has activated the clear gel solution will start to turn purple as soon as it begins to break down the iron contamination.
It is a pH Neutral formula that will react and dissolve any contamination that it comes in to contact with, from all car and van exteriors including glass, wheels and paint work.
Easy to use, no need to dilute and ready to spray.
As the name suggests, it has an unforgettable, unpleasant odour...it smells really bad, but it really works! Give it a try and see for yourself!
Also contains a impressive degreasing agent that helps loosen grime and traffic film to ensure a quicker clean to rid of contamination.
Pack size: Available in 1 Litre or 5 Litre bottles
Directions of use:
For wheels
Spray the gel/liquid formula directly on to your wheels. Allow the product to settle and dwell for approximately 5-10 minutes. Once the liquid has changed from clear to a shade of purple then rinse the wheels clean with warm water. If necessary, reapply the solution again and agitate with a soft brush.
For paint work
Apply the solution generously. Wait for the reaction and for the liquid to turn purple. Once this has happened, rinse thoroughly with water and repeat the treatment if necessary.
Excellent value for money as 10 evenly distributed sprays will cover one of your cars wheels. However, if you do have sever iron contamination feel free to spray more liberally.
Safe to use on all paint work and wheel types including glass and mirrors.
Please always refer to the instructions on the back of the bottle.
Review by Keith Gribbin - Precious Metal Detailing
First use and appraisal: The donor vehicle was a 19 Year Audi A3 which had not been washed in over three months! It made the ideal test for the TROLL’S BREATH wheel cleaner – the ultimate wheel cleaning product.
The solution was easily sprayed onto the wheels and needed time to soak into the baked-on brake dust. To simply leave and rinse in all fairness would not completely clean off any long term “baked on” brake dust and I would be forced to re-apply or work hard with a soft brush to break under the sealed layer of brake pad debris. The “debris” is caused by a build-up of fine brake pad particles. Under the heat of braking, these particles get baked onto the alloy surface. At first, this isn’t too noticeable, but over time it’ll start to show up as a dark grey film known as iron fallout which is nearly impossible to wash off with car shampoo.
PRO-KLEEN TROLL’S BREATH came in a one-litre trigger bottle with no instruction to dilute.
Upon initial application, it became apparent that TROLL’S BREATH was a thick substance, which although is easy to spray on, began to form a uniform coverage upon the alloy wheels. (I always clean one wheel at a time as this means I am less likely to leave the chemicals on for too long which could damage the painted surfaces of the alloys). It has a very pungent smell similar to sulphur which if inhaled can cause serious health issues, so please be extremely careful when using it.
The PRO-KLEEN TROLL’S BREATH immediately begins to turn a deep purple colour as it gets to work dissolving the brake dust particles. The more purple it goes, the more iron fallout is on the wheels. It naturally “pulls” in a downward direction under gravity, pulling iron contamination away from the wheels.
I prefer to agitate the product by using a soft round-headed brush which allows me to access all the intricate creases, folds and delicate rims of the alloy wheel. As I do so, the product begins to foam and turns into a dark purple/grey mix. Move your vehicle forward or back around half of a wheel turn to allow easy access to sections of the alloys that are initially facing upwards and difficult to see. This way you guarantee that the whole wheel is treated. Leave for five minutes before agitating with a brush and then wash off with cold water from a hose. I prefer to use a steady flow from a hose, and not a power washer, which might cause a backsplash up into the eyes, on the skin, or onto your clothing.
The end result was absolutely amazing and you can see from the photos that even the interior rim of the wheel has been cleaned effortlessly and they appear as good as new and in a showroom condition! These results were achieved in under ten minutes per wheel! Five minutes soaking, two to three minutes of agitation with a soft brush, and a rinse from the hose.
The product was then liberally sprayed onto the bodywork of the vehicle and began its process of dissolving over three months of grime, dirt, bird droppings and the like, effortlessly. The vehicle was once again rinsed with a hose to neutralise the solution and helped prep the car for the next stage of the detailing process, Snow Foam.
WARNING:
There are sufficient warnings on the bottle to indicate that the PRO-KLEEN product is corrosive and harmful to the eyes and skin, so always consider the direction and strength of the wind when applying. Wear safety goggles/ a face covering and gloves for additional personal protection. Always read the instructions to obtain the safest and most effective results. A freephone telephone number is also present on the bottle in case of a medical emergency along with hazard warning diagrams. A technical sheet is also available from PRO-KLEEN.
Reviews
Frequently asked questions
https://www.hygienesuppliesdirect.com/pro-kleen-tar-dah-super-powerful-tar-remover
Ask one of our experts!
We aim to answer all questions as soon as possible - often within a few hours! Although please bear in mind that during busier periods it may take up to 48 hours to receive a response. We look forward to hearing from you.
Email: | |
Phone: | |
Question: | |
Business name: | |